试验模型

shì yàn mó xínɡ
  • test model;prototype
试验模型试验模型
  1. 有可能这船不过是从展览馆弄来的一个试验模型,把几个不同的机型七拼八凑在一起的产物。

    It 's possible the ship was a developmental prototype from some showroom floor , cobbled together from several different models .

  2. FlowChamber流动试验模型

    TESTING Flow Experimental Models of a Flow Chamber

  3. 大跨距K型伸缩井架及底座试验模型设计

    Design of Test Model for K-Type Wide-Span Telescoping Derrick and Its Substructure

  4. FPS型TMD振动台试验模型设计及其减震效率仿真分析

    FPS Typed TMD Design for Shaking Table Test and Seismic Reduction Efficiency Simulation Analysis

  5. 同时利用有限元计算软件ANSYS对试验模型以及与试验模型相同跨度、跨高比和截面尺寸的门式刚架进行计算。

    The test model and another model with the same span , span-height ratio , and sectional dimensions were analyzed using the finite element analysis software ANSYS .

  6. 运用ANSYS大型软件,对试验模型进行了非线性分析,研究了模型钢筋混凝土结构的受力机理和破坏过程。

    Finite element nonlinear analysis of the segment of experimental model by large software ANSYS . the force of the actual mechanism and destruction process of the reinforced concrete structure was studied .

  7. 为研究静电放电(ESD)对微机接口电路的干扰效应,设计了一种单片机系统串行数据传输电路试验模型。

    In this paper , a typical single-chip circuit is designed to simulate serial communication interface in order to study the effect of ESD on interface of microcomputer .

  8. 200MW供热堆堆芯结构抗震试验模型设计的若干问题

    Some problems of aseismic test model design of NHR-200 core structure

  9. 试验模型隧道长100m,内径1.8m。

    The model tunnel is 100 m long , and it has a circular cross-section with an inner diameter of 1.8 m.

  10. 利用ETABS软件建立一CS板式结构试验模型(1:2.8)的等代柱计算模型并对其进行Pushover分析,分析结果与试验结果基本一致。

    This paper uses ETABS software to set up the equivalent column model of a 1:2.8 CS panel experimental structure and carry out Pushover analysis to the model .

  11. 第三,采用ANSYS有限元分析软件分别建立平压试验模型、铺装结构模型和对比模型,对铺装结构进行了系统全面的受力分析。

    Thirdly , the paper applies finite element analysis software ANSYS to respectively establish the flat crush test model , the pavement structure model and the contrast model , carrying out systematical and comprehensive stress analysis for the pavement structure .

  12. 主要研究内容如下:1.对人行桥试验模型进行了数据的采集与分析,详细介绍了试验模型以及实验过程,并对信号分析过程中FFT变换的物理意义进行了阐述。

    Collected and analyzed the data of the test footbridge model . Introduce the data collection equipments , test model and collection process , this paper expounded physical significance of FFT transform in the signal analysis process .

  13. 首先计算分析跨径为1m的试验模型斜梁桥,并将其计算结果与试验结果进行比较,组合有限单元方法的准确性得到初步验证。

    Firstly , author calculates a test model of skew girder bridge with a span of 1 m , and compares with the test result , hence validate accuracy of integrated finite element method .

  14. 组建了典型DDC控制系统的试验模型,分别在2种电磁脉冲模拟器中对其进行了干扰试验,测量了不同试验状态下DDC控制系统受干扰的场强阈值。

    A typical direct digital control ( DDC ) system was established and tested in two electromagnetic pulse ( EMP ) simulators . The interference thresholds of the DDC system under different test conditions were obtained .

  15. 第三章通过有限元软件Ansys分析试验模型,并与同尺寸的平板无梁楼盖有限元模型、密肋楼盖有限元模型、交叉梁有限元模型内力、挠度计算结果进行比较。

    In the third chapter , we made finite element analysis on the testing model by the finite element program ansys , and compared the internal force , deflection with the finite element modal of mushroom floor , joist floor and crossing beam system with the same size .

  16. 本文以ABS塑料为原料,按照动力相似理论,制作了一个比例为1:100的试验模型。

    According to dynamic similarity theory an experimental model with 1:100 ratios is made out of raw material of ABS plastic in this paper For the train movable load on the surface of bridge , full load of train is considered as the only load behavior .

  17. 运用MIDAS对试验模型各工况作了空间有限元分析,研究了各工况下模型的变形和受力状态,为试验模型测点布置提供了依据。

    The deformation and stress state of each work condition of test model was studied by establishing a MIDAS spatial model , which services for the arrangement of measuring points of the test model . 4 .

  18. 根据相似理论建立试验模型。

    The author establish experiment model according to the similarity theories .

  19. 一个临床试验模型中的参数检验和估计改进

    Test and estimation improvement for parameters in a clinical trial model

  20. 混合加速寿命试验模型下威布尔分布参数的统计分析

    Statistical analysis of the parameters in Weibull distribution under hybrid accelerated model

  21. 振动台试验模型尺寸误差分析与研究

    An Error Analysis of Shaking Table Test on Model Dimensions

  22. 一维分段混料试验模型的D-最优设计

    D Optimal Design of the quadratic segmented model on the mixture experiment

  23. 航天相机等效试验模型的研制

    A Study on Equivalent Test Model of a Space Camera

  24. 带裙房的高层建筑试验模型动特性测试

    Test on the Dynamic Property of Tall Building Model with Podium Structures

  25. 建立分析模型模拟试验模型在地震激励下的弹塑性反应,证明了该模型的有效性。

    Analytical model developed to simulate elastic-plastic seismic response is proved practically .

  26. 以一台四墙切圆煤粉炉试验模型为研究对象,对炉膛内煤粉的流动及燃烧进行了数值模拟。

    The combustion of pulverized-coal in a four-wall tangentially-fired furnace was simulated .

  27. 建立一两跨连续曲线箱梁有机玻璃试验模型。

    A two-span continuous curved box girder model was made with Perspex .

  28. 调压井试验模型设计的研究

    The study of model design about the surge chamber experiment

  29. 有依从性观测的临床试验模型的参数估计

    Parameter Estimation of a Heteroscedasticity Model for Clinical Trials

  30. 结构-ER/MR智能阻尼器系统试验模型

    Experimental Model of Structure-ER / MR Smart Damper System