模套

全自动CNC铣削和深孔钻削机床淘汰了模套中模板等零件加工的大量手控机床的作业。

Automatic CNC milling and deep hole drilling machine out of the die sleeve template parts processing a large number of manual machine operation .

当压边模套与导套之间因磨损产生间隙时，借助调节设在侧面的调节螺栓，便可消除产生的间隙；

By adjusting the lateral bolts , the clearance that is caused by abrading between the die sleeve and the guiding sleeve will be eliminated .

压铸模套板的壁厚校核

Wall Thickness Checking of Sleeve Plate for Pressure Casting Die

自恒压压力模套的新设计

Pressure ; New Design of Automatic and Constant Forcing Die

模套预应力对合金模坯强度的影响

The influence of the prestress of cases on the die strength of cemented carbide

在加热模套时，可放入少量颗粒木炭，通过木炭的燃烧消耗氧气达到减少氧化烧损的目的。

As heating die sleeve , a few grain charcoal is added and oxygen is consumed by charcoal burning so that oxidation burning loss is reduced .

但是，由于各国的“海情”有异，经济与社会发展的要求不同，在海洋法实践中遵循一个固定不变的模套是不可能的。

However , the different " situations in the seas " and different requirements for social-economic developments among various countries make it impossible to follow a constant model in practicing the law of the sea .

通过实践证明，模套与模坯之间有良好的接触面，模坯的抗张力和抗冲周力增强，从而减少和消除硬质合金模坯在使用过程中的破碎率，提高使用寿命。

The practise shows that fine contact surface between the case and the die , increased tension stress and shock resistance of die can reduce or eliminate the crushing ratio by using cemented carbide die and increase service life .

本文就滚轮式离心机滚模套球铁件的无冒口铸造进行了深入探讨，并对该铸件的铸造工艺及生产控制要点提出了自己的看法。

This article deeply discusses the casting method for nodular cast iron roller sleeve of roller type centrifugal machine with little riser and also presents the author ′ s view on its casting technology as well as main control points of production .

卡邦金刚石拉丝模镶套工艺研究

Study on Insert Process of Carbonado

目前一般采用多个二元掩模多次套刻的方法来制作连续微浮雕结构，用量化的台阶去逼近理想的轮廓。

At the present time , micro optical elements with continuous relief structure are usually fabricated by the multi-mask photolithography .

消失模铸造汽缸套毛坯的工艺研究

Study on the Evaporative Pattern Asting Process of Cylinder Sleeve Blank

主营轴承铆合模、拆套模等铆合模具。

Main Sales : Bearing riveting die , demolition riveting sets of molds for tooling .

激光直写系统的应用，可以分成一次曝光制作光刻掩模和多次套刻曝光制作器件两个方面。

Mask making with one step exposure and device making with multiple overlay exposure are applications of the system .

本机配置有大、中、小模头三套可调换，将铜齿轮内的模头及铜板上的刀片取出更换。

The machine equipped with large , medium and small die can be any of three sets of exchange , will die within the copper gear , and replacement of copper on the blade out .

轧制过程数模调优闭式套模翻修的应用

OPTIMIZATION TO MATH MODELS IN ROLLING PROCESS Application of Overhaul Closed Type Cover Die

对于用户需购标准型的导向模和挤出模套可立即发贷。

Standard tips & dies and extrusion die formulas can be delivered immediately if any order is placed .

凸模用弹性夹套固定，模具对中性好，更换凸模方便。

The punch was fixed by a spring clamp sheath , so that the die was good coaxial and convenient for exchange of the punch .

每一只导向模、挤出模套都可根据用户提供的数据设计制造，100%同轴度检测确保电缆同志轴度，从而使绝缘导线具有精确的电特征。

The100 % coaxial grade inspection can assure users of the coaxial wires and cables , thus featuring the insulted conductor with high precision of electrical property .

对无凸模导向和保护套的模具结构进行分析，提出冲裁小凸模强度核算应考虑的问题。

Both the structure of die without punch guidance and protecting jacket are analyzed , and opinions that intensity of blanking small punch should be verified are concluded .

介绍拉丝模模坯、模套的加工及模芯装镶过程中应注意的要点；

To introduce the points needed to be attended during machining the die blank and die sleeve and inserting die core .

阴模、芯棒和压模套均可浮动的拉下式压模设计实例

Example of design of floatable and withdraw type die including cavity die , core rod and die sleeve