刷涂

使用方法可采用喷涂、刷涂、擦涂等。

The application methods of spray coating , brush coating and erasing coating can be adopted .

刷涂热分解法制备Ti/SnO2-Sb2O5阳极及其性能

Performances of Ti / SnO_2-Sb_2O_5 Anodes Prepared by Brush Coating Thermal Decomposition Method

本研究由不同的涂层制备方法（刷涂法、浸涂法、气相反应法）在C／C复合材料、石墨基体表面制备了SiC涂层。

In this paper , SiC coating was prepared by different methods ( paste coating , dip coating and vapor reaction coating ) on the surfaces of C / C composites and graphites .

简介了长输管道异型管件及补口防腐的两种方法，即高膜厚PU防腐涂料刷涂法和火焰塑料喷涂方法。

This paper briefly introduced two methods for anticorrosion of special piece and repaired mouth of long transportation pipeline , i. e , flame plastic spraying and high-build PU anticorrosive paint .

以V2O5溶胶凝胶为原料，采用旋涂法、浸涂法、喷涂法和刷涂法在各种衬底上涂制V2O5薄膜。

Employment V_2O_5 sol-gel as material , V_2O_5 films on different substrates were produced by four physical coating technologies .

在20G钢管表面刷涂耐磨陶瓷复合涂层，考察了经不同温度热处理后涂层的耐磨性。

A newly developed abrasion resistant ceramic coatings is applied onto the surface of20G steel pipe , and its abrasion resistance after heat treatment at different temperatures are investigated .

再采用刷涂法，并通过对固化温度、时间等工艺参量的控制，分两步合成了聚酰亚胺PI固体薄膜。

And then adopt the law of brushing , pass the control on craft parameters such as solidification temperature , time , etc , have divided two steps and formated the inferior amine PI solid state membrane of acyl of gathering .

对浸涂、刷涂和固化处理的C/C复合材料涂层，经过热震和静态氧化试验，并用扫描电镜（SEM）和光电分析天平（TGA）作对比研究，探讨了涂层的抗氧化和失效机制。

The tests of thermal shock and static oxidation are done to C / C composite coating processed through soaking , coat brushing and solidifying . Then the coating 's anti-oxidation and mechanism invalidity are discussed through the contrast and study by using SEM and TGM .

面涂料具有较好的厚涂性，单次刷涂的干厚度达到1.1mm，具有较好的抗金属液冲刷和侵蚀特点。

The surface coating has a thick coating character of 1.1 mm with a good anti erosion character on liquid metal .

发现稀土化合物确实能提高硅橡胶与刷涂底漆的HMXCMDB推进剂或AlRDXCMDB推进剂之间的粘接强度，并且硅橡胶与HMXCMDB推进剂粘接的剪切破坏形式为硅橡胶本身的内聚破坏。

It is discovered that rare earth compounds added into silicone substrate can certainly increase bonding strength between RTV Silicone rubber and HMX-CMDB propellant or Al-RDX-CMDB propellent coated with the primer , and the failure mode of shear samples is cohesive failure of silicone rubber itself .

浓相输送管道防腐耐磨剂刷涂专机

Special paint machine of anti-corrosive and anti-friction for dense phase transfer pipe

无气涂料，空气涂料，刷涂及琨涂。

Airless spray , air spray , brush and roller .

多功能刷涂磷化剂的研制与应用

Study and application of multifunctional phosphating agent for brush coating

刷涂或辊涂时建议使用干净的中刚性毛刷或中等绒毛辊子。

Use a clean , medium bristle brush or medium nap roller .

外涂石墨机器人自动刷涂装置

Automated Brushing Equipment with Robot of CPT Outer Graphite

该产品可用刷涂、滚涂、喷涂等多种方式施工，稀释剂为二甲苯。

Application by brush , roll and spray , the thinner is xylene .

施工方式：刷涂、辊涂或喷涂。

APPLICATION METHOD : brush , roller , conventional spray or airless spray .

铁系刷涂防蚀型磷化液研究

Studies on Iron Family Elements-containing Rustproof Phosphating Liquid

环保型刷涂磷化粉在集合式电容器外壳上的应用

Application of Environmental-friendly Monocomponent Phosphating Powder to the Case of the Assembling Shunt Capacitor

清洁型刷涂铁系磷化液研究

Study on Clean and Brush-painting Ferric-system Phosphating Solution

刷涂型无溶剂聚氨酯涂料的制备和研究

Preparation and Study of Brushable Solventless Polyurethane

小面积施工使用刷涂或辊涂。

Brush or roller for small areas .

刷涂或辊涂只用于小面积施工或修补，且避免重涂。

Brush or roller for small areas and touch-up only . Avoid re-brushing and re-rolling .

刷涂型磷化液的研制

Development of a Brush Phosphating Solution

刷涂结束后，毛刷应由指定的稀料清洗。

After the painting work is finished , the brush should be well cleaned using specified thinners .

利用简便的刷涂法在钢基体表面制备了石墨固体润滑涂层。

The simple brush-painting method was utilized to prepare the graphite solid lubrication coatings on the steel substrate .

跟我们的粉底类似，但不会有很大的遮盖能力，这阴影粉需要用刷涂，单独或在粉底后使用。

Similar to our foundation , but not made for much coverage , this bronzer is brushed on alone or over foundation .

可溶性部分的去除可以加快由刷涂或喷涂在暴露聚合物层溶剂或混合溶剂。

Removal of the soluble portions can be expedited by brushing or spraying the solvent or solvent mixture on the exposed polymeric layer .

本文介绍了一种铝冶炼行业氧化铝浓相输送管道防腐耐磨剂刷涂专机技术。

This paper introduced a special machine technology of applied in aluminium metallurgy profession for dense phase transfer pipe paint anti-corrosive and anti-friction .

在采用刷涂工艺时，如果每次刷得太厚太粘稠或者在前次施工涂层未彻底干燥之前即进行后续施工都可能导致过多气泡的产生。

Using a brush to apply a coating which is too viscous or brushing the same area repeatedly before it dries can cause bubbles .