渗碳钢

综合看来，渗碳钢中加入0.2～0.4%的Mo从技术上和经济上考虑是最佳的。

Comprehensively , The addition of 0.2-0.4 % Mo to carburizing steel is optimum from both technical and economic sides .

Cr－Ni－Mo合金渗碳钢由于钢中合金元素和碳的偏析，经一般退火后存在比较严重的带状组织。

Because of the segregation of alloy element and carbon in steel , there exists severe band structure in the carburizing steel containing Cr. Ni and Mo after normal annealing .

ManB&W镍铬钛排气阀的检修铬镍渗碳钢的残余奥氏体

Inspection and maintenance for MAN B & W nickel-chromium-titanium exhaust valve

X射线衍射法测定渗碳钢中残余奥氏体

Measuring retained austenite of carburize layer of low carbon alloys with X-ray diffraction method

用冲击强度测定渗碳钢的S-N曲线及突发性断裂强度

Determination of S-N Curves and Instant Fracture Strength of Cemented Steel by Impact Strength

采用透射电镜研究了深冷处理对SAE4820渗碳钢TEM组织的影响。

The effect of cryogenic treatment on the TEM microstructure of SAE 4820 carburized steel was studied by means of Transmission Electron Microscope ( TEM ) .

用Brugger试验方法测试渗碳钢的S-N曲线及评价渗碳齿轮抗突发性断裂强度进行了讨论和评述。

The application of Brugger impact method in testing of S-N curves of cemented steels and evaluating of instant fracture strength of cemented gears has been discussed and investigated .

渗碳钢疲劳内裂纹的萌生和扩展

Initiation and Propagation of Internal Fatigue Cracks in a Carburized Steel

端磨渗碳钢时磨削烧伤的预测和控制

Forecast and control on grinding burn of cementation steel when end-grinding

汽车齿轮用渗碳钢的发展现状及前景

Developing Status and Future of Carburizing Steel Used for Automotive Gears

几种渗碳钢的接触疲劳和弯曲疲劳性能

Contact Fatigue and Bend Fatigue Property of Kinds of Carburizing Steels

合金渗碳钢表面低温气体多元共渗研究

Study on Low Temperature Gas Multielement Co-penetration on Alloy Carburizing Steel Surface

渗碳钢在接触疲劳过程中表面层的残余应力

The residual stress on surface layer of carburized steel during contact fatigue

两种合金渗碳钢等温正火工艺的研究

Study on the Isothermal Normalizing of Two Low Carbon Alloy Steel Parts

渗碳钢磨削烧伤及裂纹的试验研究

Experiment research on grinding burning and crack of carburized steels

渗碳钢变温渗碳过程分析

The analysis of altering temperature carburizing process of carburizing steels

合金渗碳钢锻件等温正火的研究

Study on the Isothermal Normalizing of Carburizing Alloy Steel Forgings

表面滚压对渗碳钢缺口疲劳强度影响的研究

Study on effect of surface rolling on notched fatigue strength of carburized steel

轧机轴承渗碳钢的选择和渗碳层的设计

Selection of Carburizing Steel for Rolling Mill Bearings and Design of Carburized Layer

新型空冷贝氏体渗碳钢的研究渗碳钢的深冷强化

A Novel Air Cooling Bainite Carburized Steel Study on Cryogenic Strengthening of Carburized Steel

研究了硅对准贝氏体渗碳钢渗碳组织与性能的影响。

Effect of silicon on microstructure and properties of meta-bainitic carburizing steel were studied .

稀土深层渗碳钢的研究

Study on Rare - earth Deep Carburizing Steel

渗碳钢在裂纹萌生前的疲劳行为

Fatigue behavior of carburized steel before crack initiation

浅谈合金渗碳钢带状组织

Discussion on Banded Structure of Carburizing Alloy Steel

铬镍渗碳钢的残余奥氏体

Retained Austenite of Cr - Ni Carburizing Steel

渗碳钢的淬透性与热处理畸变

Hardenability of Carburizing Steel and Heat Treatment Distortion

渗碳钢件磨削裂纹的产生及其工艺分析

Occurrence of Crack on Carburized Steel Pattern in Grinding Process and Its Technique Analysis

准贝氏体渗碳钢在汽车齿轮上的应用

Meta Bainitic Steel Carburized for Automobile Gears

渗碳钢扭转变形时断裂行为和渗层厚度对接触疲劳的影响

Effect of torsional deformation fracture behaviour and carburized depth on contact fatigue strength for carburized steels

结果表明，晶粒尺寸越小，渗碳钢的疲劳极限越高。

Results show that the smaller the grain size is , the higher the fatigue limit is .