排气口

MWM发动机在普通四冲程发动机的气缸侧壁增加了一个排气口，且由气门控制其开闭，通过处于不同位置气门的配合工作，从而实现其各种工作模式和工作过程。

MWM engine add an exhaust port at a four-stroke engine cylinder wall , and it be controlled to opening or close by a valve , this structure can make the engine has different working mode by different valve working together .

至少这种设计有一个较大的排气口比进气道，即使不是由得多。

At least this design has a larger exhaust port than the inlet port , even if not by much .

产品流进从汲取管，从阀门排气口流出，流程形状象字母C一样。

The product flows into the dip tube and out the valve outlet in a flow path shaped like the letter " C " .

发动机排气口快速取样及示踪HC喷射的研究

Time Resolved Sampling and Tracer Injection Studies Related to Exhaust Port Hydrocarbon Oxidation

RTM工艺中注射口和排气口的研究

Study on gate / vent arrangement in resin transfer molding process

火花点火式发动机排气口HC氧化的研究

A Study on Exhaust Port Hydrocarbon Oxidation

本文论述TK发动机排气口测试故障的采样理论，仪器的基本原（？）

The paper deals with the theory of exhaust-gas Sampling of TK engine for trouble diagnosis in situ .

通过对RTM工艺中注射口及排气口的合理布置研究来提高RTM工艺制品的复合效果。

The arrangement of gates and vents were studied to improve the compound effect on the RTM product .

在RTM工艺中，注射口和排气口的位置是工艺设计中最重要的变量之一。

In the RTM process , gate / vent location is one of the most important variables in the process design .

用于液体产品提取的阀门也配有标准的CGA的排气口，但它不同于用于气体提取的排气口。

Valves provided for the withdrawal of liquid product are also equipped with standard CGA outlets but differ from connections used for gaseous withdrawal .

COREX熔融气化炉风口回旋区的物理模拟不可堵塞炉门或排气口，以免产生过热或冷却不完全等故障。

Physical Simulation of Raceway in COREX Melter Gasifier Blockages to the door or oven vents can cause overheating or other failures in the cooling system .

DISS接头是一种衬垫型接头，由阀门排气口、母、接口和衬垫组成。

A DISS connection is a gasketed type that consists of the valve outlet , nut , nipple , and gasket .

带排气口的9D双止回阀适用于非健康危害、续压力应用场合，用于防止反虹吸和反压力。

The9 D Dual Check with Atmospheric Vent is designed for use on non health hazard , continuous pressure , point of use applications for protection against backsiphonage and backpressure .

本文讨论了用网格间距法设计最佳注射口和排气口位置，寻找RTM工艺充模过程中的最佳辅助注射口的三线形法以及对多注射口的RTM工艺进行了分析。

This paper studies the optimum arrangement of gate and vent locations for RTM process design using a mesh distance-based approach and the trigram method to find optimal auxiliary injection gate locations for successful mold filling and the analysis with controlled multiple gate resin injection in resin transfer molding process .

通过稳定工作电压在38kV￣42kV，调整电晕丝中心位置，在蒸汽伴热管上增设排气口等措施，确保了电捕焦油器的连续运行，成功地提升了电捕焦油器的开工率。

And by ensuring the working voltage to 39kV ~ 42kV , and adjusting the central position of the corona wire and adding an exhaust at the steam tracing , the electro tar precipitator can be operated continuously , and the on stream factor of it has been extended .

发动机气门的二种型式是：进气口和排气口。

The two types of engine valves are intake and exhaust .

将你的汽车排气口瞄准您的脚-而不是你的眼睛。

Aim your car vents at your feet & not your eyes .

为了通过检测，目测检查排气口全开。

Visually inspect that the vent is fully open to pass test .

排气口的蓝色火焰划破黑暗。

The blue flame of the exhausts stabbed the darkness .

准备连接钢瓶时，慢慢地松开阀门排气口密封。

Loosen the valve outlet seal slowly when preparing to connect a cylinder .

替换钢瓶排气口密封和阀门帽。

Replace the cylinder outlet seal and valve cap .

液环式氯气泵排气口始角的确定

The Determination of the Starting Angle of the Discharge Port in Liquid-Ring Chlorine Pumps

部分科学家认为深海排气口（即大家熟知的海底烟柱）孵育了第一批生命。

One camp says that deep-sea vents known as black smokers nurtured the first life .

两天后，我还在汽车排气口掏令人反胃的玉米面豆卷

Two days later , I am still digging regurgitated tacos out of the car vents

排气口的温度会随着当天的温度儿变化。

The temperature at the vents will vary depending upon the temperature of the day .

我将开启安全排气口。

I will begin emergency venting .

如果需要或需要，一个排气口狂热者和新鲜的空气破坏装置也可能是附加的。

If desired or needed , a vent fan and ozone destruct device can also be added .

发动机在腹部凸起采用一个椭圆形进气口和圆形排气口。

The engine is a bulging jet on the belly with an oval air intake and round exhaust .

不可堵塞炉门或排气口，以免产生过热或冷却不完全等故障。

Blockages to the door or oven vents can cause overheating or other failures in the cooling system .

所述左腔室内对应于排气口处设有加热器。

In the left chamber is arranged with a heater corresponding the position of the air outlet opening .