异步轧制

异步轧制对316L不锈钢组织与性能的影响

Effect of cross shear rolling on microstructure and properties of 316L stainless steel

异步轧制对高纯铝箔冷轧织构的影响

Effect of cross shear rolling on deformation textures of high purity aluminum foils

S异步轧制法及其应用H型钢的轧制与发展

ASYNCHRONOUS ROLLING AND ITS APPLICATION Rolling Process and Development of H Sections

全异步轧制的塑性力学和O.霍夫曼公式

Plasticity of perfect full cross shear cold rolling and o. hoffman 's formula

在各种轧制方式中，先异步轧制两道次的冷轧织构较好，试样中的γ织构组分较多，有利于在高温退火过程中向G（oss）织构转化；

Among different rolling methods the rolling textures of sample rolled by asynchronous rolling two passes are beneficial to anneal .

冷连轧机的IPV异步轧制

IPV asynchronous rolling in continuous cold strip mill

结果表明，异步轧制单位压力分布仍具有峰值；搓轧区占变形区比例x越大，异步轧制的降压效果和摩擦峰的削减作用越大；

It was found that the frictional peak in the specific pressure distribution still exists under asynchronous rolling , the larger the x ( ratio of cross-shear zone to deformation zone ), the greater the effectiveness of reduction in pressure and frictional peak hight .

张直异步轧制厚度小于1mm的黄铜带时，两辊侧单缸压力分布基本相同，但在无张力异步轧制时，普遍存在两辊则单位压力分布不对称现象。

When the brass strip with thickness less than 1-mm is rolled by asynchronous rolling with tension , the distribution of side specific pressure for two rolls is the same .

研究了异步轧制的道次压下量、轧制温度、轧制路径、异速比等工艺参数对AZ31镁合金显微组织、晶粒取向和力学性能的影响规律。

The influence of processing parameters including pass thickness reduction ratio , rolling temperature , rolling route and mismatch roll speed ratios on microstructure , crystal orientation and mechanical properties are investigated .

本文通过实测，研究了同径异步轧制厚度小于1mm的黄铜带时，单位压力沿纵向的分布规律，并系统地分析了各轧制参数对张直异步轧制和无张力异步轧制单位压力分布的影响。

The specific pressure distribution of asynchronous rolling along rolling direction was experimentally studied in this paper using 1 mm thick brass strip as rolling-stock . The effect of rolling parameters on the specific pressure distribution with or without tension was analysed .

采用异步轧制方式将0.75mm厚的工业取向硅钢板材冷轧至0.35mm，然后用工业退火工艺对板材进行热处理，研究了剪切变形条件下的织构形成与转变机理。

Commercial grain oriented silicon steel was cold rolled from 0.75 mm to 0.35 mm by cross shear rolling ( CSR ) mill , followed by industry annealing . The mechanism of texture formation and transformation under the condition of shear deformation was analyzed .

双金属固相复合异步轧制新工艺

New Rolling Process for Cladding Bimetal Materials at Unequal Roll Speeds

异步轧制时的特征角与变形区长度的计算公式

Formula for characteristic angle and asynchronous region length of asynchronous rolling

双金属异步轧制压力的测试实验研究

An Experimental Study of Rolling Pressure for Asymmetrical Composite Rolling

固相异步轧制复合双金属材料工艺条件的确定

Determination of technological conditions in solid-phase asynchronous rolling of bimetal

异步轧制简化的无摩擦峰理论

A simple theory of friction - free hill in cross shear rolling

异步轧制高纯铝箔织构控制的研究

Investigation on Texture Controlling of High Purity Aluminum Foils by Cross Shear Rolling

全异步轧制的理论解析及其实现

Theoretical analysis and Realization of the complete asynchronous rolling

异步轧制法在平整机上的应用

Application of asynchronous rolling process to the temper mill

全异步轧制过程的理论研究

The Theoretical study of Entire Cross Shear Cold Rolling

异步轧制的过程的有限元模拟

Simulation on Asynchronous Rolling Process by Finite Element Method

异步轧制自激振动的研究

A study on the self-excited vibration in asymmetrical rolling

异步轧制在铜合金带材生产中的应用

The application of asynchronous rolling system in the production of copper alloy sheets

铜/钢双金属板异步轧制复合机理研究

Bonding Mechanism of Cu / Steel Clad Sheet in Asymmetrical Rolling of Bimetal

S异步轧制前滑模型的研究

On the model for forward slip in s-asynchronous rolling

中高轧辊，凸芯轧辊异步轧制条件下高锰钢的显微组织与加工硬化机制

Microstructure and work-hardening mechanism of high manganese steel processed by asymmetrical cold rolling

异步轧制对二次再结晶取向硅钢磁性能的影响

The Effects of Asynchronous Rolling on the Magnetic of Two Crystallization Grain-Oriented Silicon Steels

这是由异步轧制过程中纯铁产生的剪切应变、等效应变分布不均匀导致的。

It is resulted from the distribution of the shear strain and equivalent strain .

锥辊楔形异步轧制力矩的研究

Rolling moment of conical rollers during asynchronous rolling

异步轧制取向硅钢的织构形成与转变机理

Mechanism of Texture Formation and Transformation in Cross Shear Rolled Grain Oriented Silicon Steel