加热板

加热板铆合模具的设计制造

Design and Manufacture of the Riveting Die for the Heating Plate

轮胎定型硫化机加热板的改进

Improve on Heating Plate of Tyre Shaping Press Vulcanizer

采用PID控制规律和可控硅过零触发方式调节加热板加热功率，设计了过零脉冲产生电路和可控硅触发电路。

Using PID control law and triac zero-crossing trigger way to adjust heating power of heating block , zero-crossing pulse generator circuit and thyristor trigger circuit is designed .

在热水中的大部分RMI的房子里来，由于这些加热板的结果。

Most of the hot water in the RMI house comes as a result of these heating panels .

在气敏薄膜的导电机理和传热学中的有限元理论的基础上，设计了封闭膜式微加热板的传感器，利用ANSYS对其进行温度场的有限元模拟。

On the basis of the electrical conduction principle of the gas sensing film and the theory of finite element method of heat transfer , a closed membrane type gas sensor with micro hot-plate was designed . Finite element analysis of the designed sensor was implemented by ANSYS .

香蕉冻干过程中参数较佳的工艺条件建议为物料厚度选取5～7mm，采用速冻方法冻结，加热板温度设定45℃，干燥室真空度控制于20～30Pa。

The quick freezing method of bananas , material thickness of 5mm ~ 7mm , heating temperature of 45 ℃, and 2 0 ~ 30 Pa vacuum for drying chamber were optimum technical conditions for drying of bananas .

因此采用感应方式来预热加热板是一种可行的方法。

So It induction heating is a feasible method to use .

角膜热成形术交流电电热器加热板温度的变化规律

Thermal Characteristic of Hot Plate in Alternating Current Electric Heater

加热板上蒸发液滴动态特性的实验

Experimental investigation of dynamic evaporation characteristics of liquid droplet on heated surface

另外，加热板表面涂有耐高温防腐蚀的涂层。

Additionally , the heating plate is coated with heat-resistant and anti-corrosion coatings .

加热板与矽晶圆在启始状态（加热前）。

Hot plate with silicon wafer in initial configuration ( before heating ) .

基于单片机的昆虫加热板温度测控系统设计

Design of Insect 's Heating Block Temperature Measuring and Controlling System Based on SCM

加热板可微调。

Heating plate can be fine adjusted .

箱盖内采用硅橡胶加热板加热系统，保证箱盖内干燥不漏水。

Silicone rubber heating board system equipped on cabinet cover to ensure drying within cabinet cover .

交流电电热器加热板温度的变化规律电热器蓄热技术

Thermal Characteristic of Hot Plate in Alternating Current Electric Heater The Heat Storage Technique of Electric Heater

文章论述家用交流电热器加热板的传热模型，得出其温度振荡解，供热设计使用。

A solution of its temperature oscillation has been got for the purpose of the heating design .

影响主次顺序为预冻速率、干燥室压力、加热板温度。

The influencing sequence from significant to common is pre-freeze rate , dry chamber pressure and board temperature .

因此对加热板的设计要求、温度检测及控制技术等进行了详细的阐述。

Therefore , In this paper , design requirements , temperature detection and control technology are introduced in detail .

加热板为国内独一无三的整体形结构，符合食品卫生要求和杜绝了加热了加热板的渗漏。

The heating plate has unique unitary structure , meeting the requirement of food sanitation and avoiding its leakage .

沥青路面热再生机组燃气红外线加热板温度控制系统的设计研究

Design and Study of Gas Infrared Radiation Heating Board Temperature Control System for Hot-Regenerating Machine of Asphalt Road Surface

通过实验研究了内置均匀加热板的垂直矩形通道入口段混合对流换热的温度场和阻力特性。

This paper investigated the behaviors of flow and heat transfer of single-phase in rectangular microchannels with three-dimensional numerical analysis .

结果表明：冻干厚度、加热板温度、冻干室压强是最重要的三个过程参数；

The results indicate that drying thickness , radiant temperature and pressure of drying chamber are the most three significant factors .

主要介绍了在纺丝生产线中，采用MCS-51单片机对多个部位加热板进行温度控制。

How to control the temperature of the multi-positions heater plates with MCS-51 single-chip microcomputer in spinning production line was introduced .

实验一装置：加热板与矽晶圆（右）连接至感温棒（左）。

Lab 1 apparatus : hot plate heater with silicon wafer ( right ), connected to a temperature probe ( left ) .

对准，调整掩模和晶片之间的位置。加热板与矽晶圆降低至加热位置。

Act of moving a mask or reticle to match up alignment marks . Hot plate with silicon wafer lowered to heating position .

发热管与加热板注为一体，安全耐用热发热均匀，热导性强。

The radiation pipe and the hot plate as a whole , safe and durable heat uniform heating , thermal conductivity and strong .

即使在实验条件下加热板内各层温度，使其呈周期性波动，但室内地板表面温度分布仍然非常均匀。

Although the temperature inside the panel fluctuated periodically in the experiment , the temperature on the surface of the panel was basically uniform .

本文对轮胎定型硫化机的加热板略做讨论，并介绍了一种先进的加热板结构形式。

This paper was a preliminary discussion for heating plate of tyre shaping press vulcanizer , and introduces a form of advanced heating plate .

我们分析其原因，发现气密性并不好，加热板处的胶水并不能保证密封性。

Then , we found that gas tightness had some problem , because gluewater of the heat copper of engine didn 't pledge gas-tightness .

注意参考号，与中间轴配对，只能一起安装，使加热板受热，向上推至顶部。

Note reference number , paired with intermediate shaft , only install together , warm on heating plate , push on up to stop .