标准板

以聚四氟乙烯（F4）粉压制板作为反射标准板，给出了F4标准板及所测样品在双向反射分布函数测定仪上的测量数据。

The powder pressboard of F4 ( polytetrafluoroethylene ( PTFE )) was used as reflection standard board . The data of sample and standard board measured by BRDF were obtained .

实地光谱测量采用NASA海洋光学测量规范推荐的水面之上光谱测量法，分别测量标准板、水面和天空光的辐照度，计算水面之上遥感反射率。

Above-water spectrum measurement method recommended by NASA ocean optical measurement criteria was employed to measure the in-situ spectrum of surface water . The radiance of standard plate , water surface , and sky illuminance was measured , respectively , to calculate the remote sensing reflectance of the water surface .

本文还对格网标准板的误差进行了分析。

The article analysed the errors of the standard plate too .

待检测板信息与标准板信息进行比较；

To compare with the board which measure information and standard board information .

黑色石英晶体光泽度标准板的研制

Preparation of Black Quartz Standard Glossiness Plate

高精度格网标准板的研制

Manufacture high precise standard plate

最后根据定标标准板对各类划痕、缺陷等不同疵病特征（如长、宽、面积）进行分析和评估。

The different defects size feature ( e.g. length , width , area ) are analyzed and evaluated by criterion .

利用标准板定标法，在外场环境对1∶8缩比模型进行了实际测量，获得了缩比模型散射截面的实验数据。

Actual measurements were made for obtaining the LRCS of the scale-model by utilizing standard scatter board in the outfield .

按照轧机执行机构板形控制的能力设置标准板形模式，可以对任意复杂形式的板形缺陷进行控制。

Standard shape patterns are set up according to the shape control capability of the actuating units in the rolling mill , so that shape defects of any type can be controlled .

基于摄像机的投影矩阵和标准板平面方程完成了投影仪的标定。最后，研究了通过摄像机和投影仪的标定参数计算物体表面三维信息的方法。

The calibration of the projector is accomplished on the basis of camera projection matrix and plane equation of the calibration plate . Lastly , the three-dimensional position calculation is carried out by using the parameters of the camera and the projector .

基于ANSYS对非标准封板的应力线性化分析

Analysis of stress linearization to non-standard seal plate based on ANSYS

基于ANSYS对非标准封板的有限元分析

Finite Element Analysis of Non-Standard Seal Plates Based on ANSYS

在MATLAB软件环境下介绍软件的设计方法，并给出了高炉煤气标准孔板设计计算实例。

Based on MATLAB , the software 's design process is introduced and the application examples in blast furnace gas standard orifice 's design is presented .

基于半导体激光器恒温控制器的GPIB标准接口板的设计

The Design on GPIB Standard Interface based on Constant Temperature Controller of Semiconductor Laser Diode

讨论了一种基于低功耗单片机MSP430的天然气标准孔板智能流量积算仪的设计。

The design of an intelligent flow totalizer based on single chip computer MSP430 with low power consumption is discussed .

在原软件基础上编制了USB总线下的激光粒度测试软件LSA，并使用新的激光粒度测试系统完成了对标准粒子板的测试实验，得到了满意的结果。

Improving the LSA software package and completing the experiment of measuring the standard-particles board by using the new laser particle size measuring system .

采用自适应Projection算法对标准粒子板和国家标准物质进行测量实验，并与已有的改进下降因子的Projection算法、引入渐变下降因子的Projection算法的实验结果进行了比对。

Using adaptive Projection algorithm to measure the standard particle board and national standard material , compared the result with improved Projection algorithm which introducing an increasing fine coefficient and Projection algorithm which introducing an improved fall coefficient .

介绍了在无氧铜杆炉生产设备基础上研制微机控制系统，该系统采用PC总线工控机及配套的标准接口板，运用变速积分PID控制算法；

This paper introduces the control system on the base of the no oxygen copper rod furnace facility . This system uses PC bus industrial control computer and complete standard interface cards . It is applied non uniform velocity PID control algorithm .

按照JEDEC标准对板级跌落实验的要求测试了有铅和无铅焊点的球栅阵列封装。

Leaded and lead-free BGA ( ball grid array ) components were tested in board level drop test defined in the JEDEC ( Joint Electron Device Engineering Council ) standard .

第三章主要介绍了对CPU-1432进行BSP开发的过程，选用标准Pentium板级支持包，针对硬件平台进行修改，并通过几种不同的方法移植到CPU-1432上。

Chapter 3 describes the process of developing BSP ( Board Support Packet ) in several methods , choosing BSP for Pentium and modifying it according hardware platform and explanting .

目前对油田伴生气的计量基本上都是采用标准孔板节流装置配用CWD-430双波纹管差压计来进行计量。

At present , the measurement of associated gas is basically made by using standard orifice control device together with CWD-430 differential pressure guage with double-ply bellows .

激光扫描制备标准粒子板的研究

A New Method of Making Calibration Reticles by Laser Beam Scanning

气提泵中标准孔板流量计特征

The Characteristics of Standard Orifice Flow Meters in an Airlift Pump

重点介绍了内锥流量计的各项特性与技术指标，并与标准孔板流量计作了比对，说明内锥流量计优于标准孔板。

Various characteristics and specifications of inner flowmeter are described in detail .

天然气流量的标准孔板计量方法SYL04&83

Natural Gas Flow Rate Measurement Method by Standard Orifice plate

一种提高标准孔板流量计计量精度的方法

A method of raising the Precision for standard hole - board flowmeter

非标准交接板梁组合结构的有限元建模新方法

A New Finite Element Model for Plate-Beam Combined Structures with Non-standard Connection

测量多组份气体流量的标准孔板的计算方法

Orifice Plates Calculation Method for Multi-Constituent Gas Flow Measurement

激光粒度仪方孔标准粒子板的修正系数

The Correctness Factor of Square Standard Particle Plate Used for Laser Particle Sizer

基于神经网络的标准孔板气体流量测量

Standard Orifice Measurement of Gas Flow Based on ANN