烧结温度

烧结温度对Y2Ba4CuNbOx粉体物相成分及显微结构的影响

Effect of sintering temperature on phase composition and microstructure of Y_2Ba_4CuNbO_x powder

烧结温度对Al2O3/SiC（n）纳米复相陶瓷性能的影响

Influence of Sintering Temperature on Performance of Al_2O_3 / SiC ( n ) nano-composite Ceramics

烧结温度和热处理对ZnO压敏陶瓷的影响

Effect of Sintering Temperature and Heat-treatment on ZnO Varistor Ceramics

烧结温度等参数对Fe2O3粉末烧结密度影响的试验研究

The experimental research on sintering temperature to fe_2o_3 powder sintering density incineration test

V2O5含量与烧结温度对MnZn铁氧体性能的影响

Effects of V_2O_5 content and sintering temperature on magnetic properties of Mn-Zn ferrites

SiC–Cu/Al复合材料的硬度随烧结温度的升高的变化成马鞍状。

The saddle - shaped profile of the hardness with sintering temperature was detected .

过去CeO2基电解质材料所需要的烧结温度较高。

In the previous work , CeO_2-based electrolytes needed a high sintering temperature .

烧结温度对Al2O3+WC陶瓷强韧性的影响

The Effect of Sintered Temperature on the Strength and Toughing of Al_2O_3 - WC Ceramic Composite

烧结温度对WC增韧Al2O3陶瓷耐磨性的影响

The Influence of Sintering Temperature on Wear Resistance of Al_2O_3 Ceramics Toughened by WC

1800℃是适宜的制备高耐温性SiC纤维的烧结温度。

1800 ℃ was an ideal sintering temperature for producing high temperature resistant SiC fiber .

以TiO2纤维制备微滤膜过程中烧结温度的影响

Effect of sintering temperature on microfiltration membrane prepared with TiO_2 ceramic-fiber

研究了Ti基底处理、烧结温度控制以及悬浮液配方等因素对涂层结合强度的影响。

Influence of substrate treatment , sintering temperature and the dispensation of suspension on the bonding strength were investigated .

本文着重讨论了FePCCu合金的成分、组织与性能之间的关系，研究了不同的铜含量、碳含量和烧结温度对合金的组织、机械性能及烧结收缩的影响规律。

The effects of different copper and carbon contents and sintering temperatures on microstructure , mechanical properties and sintering shrinkage of alloys are also described .

H（ci）与最大磁能积（（BH）（max））随预烧结温度的增加而线性增加，尤其是在高温阶段。

H_ ( ci ) increased greatly with pre-sintering temperature increasing , especially at high temperature .

随着烧结温度的升高，ZnO压敏陶瓷的晶粒逐渐长大，结构逐渐致密；

Following increasing of sintering temperature , grain of ZnO ceramic is grown up and structure is compacted gradually .

研究了Fe－Cu－Me铁基减摩材料的成分配比和烧结温度对其物理力学性能的影响。

The influence of composition and sintering temperature of Fe-on-Me iron based antifriction material on its physical and mechanical properties has been studied .

本文研究了超细粉3mol%Y2O3&ZrO2陶瓷的组织结构及力学性能，结果表明，随烧结温度升高，晶粒长大，单斜相含量增多。

The microstructure and mechanical properties of superfine-powder 3mol % Y_2O_3 & ZrO_2 ceramics were studied in this paper .

结果表明BN的加入降低了材料的烧结温度；

The sintering temperature reduce by addition of BN ;

其烧结温度为1400℃时，其相对密度为95.63%，电阻率为78.37Ω·cm。

The relative density of the specimen fired at 1 400 ℃ was 95.63 % , and the resistivity was 78.37 Ω· cm .

研究结果表明：烧结温度越高，越有利于晶粒粗化，形成大块板状WC晶粒；

The results show that high sintering temperature favors the formation of large plate-like WC grains .

一Tic一CO复合粉体的制各及复合材料的研究20043其抗弯强度和断裂韧性均随烧结温度的升高而下降。

The bending strength and fracture toughness of the ultra fine ATC ceramic all fall down with the growing sinter temperature .

主要研究了烧结温度对TiO2压敏陶瓷电性能的影响。

The influence of sintering temperature on the electric property of TiO_2 varistor ceramics is mainly analysed in this article .

Bi基材料具有较低的烧结温度和优良的介电性能，因而受到了广泛的关注。

Bismuth-based microwave dielectric materials have at-tracted wide attention because of their relatively low sintering temperature and excellent dielectric properties .

烧结温度对全稳定ZrO2陶瓷显微结构及性能的影响

The effects of sintering temperatures on Microstructure and properties of fully stabilized zirconia

通过分析烧结温度、Na2O含量对烧结和析晶的影响，选择了合适的烧结条件，控制烧结和析晶程度，获得了既有足够的自身强度，又有一定的结合强度的多孔玻璃陶瓷。

By analysing the effect of sintering temperature and Na_2O content on sintering and crystallization , sintering condition for bioglass can be optimized .

反应烧结温度对Si3N4-SiC材料性能的影响

Effect of reactive sintering temperature on properties of Si_3N_4-SiC refractories

研究了SPS烧结温度和添加晶粒抑制剂对显微组织与HRA硬度的影响。

The influences of SPS temperature and grain inhibitor on microstructure and hardness were studied .

确定了CaOAl2O3SiO2系统玻璃颗粒的起始烧结温度（Ts），起始析晶温度（Tc）。

The incipient sintered temperature ( Ts ) and the incipient crystallization temperature ( Tc ) of the glass particles were defined .

对该系统B位氧化物前躯体的合成温度进行了探索，同时对烧结温度和锆钛比对该系统的压电、介电以及机电等性能的影响进行了研究。

The calcination temperature of the B-site oxide Precursor is optimized . The effect of the sintering temperature and the Zr / Ti ratio on the properties of piezoelectric , dielectric and electromechanical properties were investigated .

随着烧结温度的提高和保温时间的延长，Nd∶YAG陶瓷的密度增大，晶形发育完整，透过率提高。

The density of the ceramics increases , and the transmittance improves gradually with the increase of the sintering temperatures and the prolonging of the holding time .