模具钢

高耐磨模具钢GM碳化物及显微组织研究

Carbide and Microstructure of Cold-Worked Die Steel GM with High Abrasion Resistance

高韧度耐冲击冷模具钢（DS钢）的合金化及热处理

Alloying and Heat Treating of Cold Die Steel DS with High Toughness and Impact Resistance

工模具钢退火用C曲线的测定及其应用

C-Curves of Tool Steels for Annealing and Their Application

基于web的金刚石钻头模具钢体设计∏型钢剪料模

Web-based design of die and steel blank for diamond bit Blank die using in Π form steel

析出硬化型热作模具钢（PH）的研制

Study of Hot-Worked Die Steel PH of Precipitation Hardening Type

Cr（12）系列模具钢的工艺研究

Cr _ ( 12 ) - Series Die Steel Process Study

模具钢表面连续激光沉积TiN类薄膜的研究

Study on Continuous Laser Deposition of TiN Thin Films on Die Steel Substrate

模具钢表面真空钎焊WC涂层的研究

Study of Vacuum Brazing WC Coating on A Die Steel Surface

冷作模具钢LD钢的加工及精密磨削

Working and Precision Grinding of LD Steel as a Cold - Working Die Steel

PCVD法在模具钢表面沉积Ti（CN）涂层的研究

Ti ( CN ) Layer Deposited on Tool Steel by PCVD Technique

D2模具钢轧材碳化物均匀性的检测与分析

Detection on Inhomogeneity of Eutectic Carbide of Rolled D2 Die Steel

国产A2冷作模具钢的性能和应用

The Properties and Applications of the Cold Work Die Steel A2 of Chinese Made

冷作模具钢D2锻造温度的探索

Study on Forging Temperature of Cold Worked Die Steel D2

冷作模具钢D2钢高温变形行为的研究

Research on high temperature deformation behavior of cold working dies steel D2

D2冷作模具钢的回火转变研究

Investigation on Tempering Transformation of Steel D2

介绍了开发新型模具钢的重要性，介绍了太钢生产的一些模具钢品种，重点介绍了开发出的热作模具钢A和塑料模具钢B。

The importance of developing new die steel , and some die steel , specially hot forging die steel A and plastic die steel B produced by TISCO have been introduced in this article .

新型铸造热作模具钢MIG焊接接头组织及性能的研究

Study on Microstructure and Properties of MIG Welded New Type Cast Hot Work Die Steel Joints

因而，Si减弱了铝合金熔体与模具钢间的相互作用，从而降低压铸合金的焊合倾向性。

Therefore , the element Si in aluminum alloy reduces the interaction between die steel and aluminum alloy melt and reduces the soldering tendency of aluminum die casting .

讨论了数控磁性研抛工艺在LD新型模具钢上的使用情况。

This paper discusses the technology of the NC magnetic abrasive finishing of LD ( mould steel ) based on the experiments .

表面处理对提高模具钢Cr2使用寿命的影响

Effect of Surface Treatment on Service Life of Die Steel Cr2

稀土在H13模具钢低温粉末渗硼中的应用

Application of Rare Earth Additives in the Low Temperature Powder Boronizing

新型Cr-Mo-V精铸热作模具钢的研制

Development of a New Cr-Mo-V Precision Casting Hot Working Die Steel

铸造H13模具钢在热挤压模中的应用

Application of Cast Dies Steel H1 in Thermal Extruding Die

本文结合实例对淬硬模具钢高速加工的制造技术与CAM数控编程等方面进行了分析。

In this article , the writer focused on the quenching rigid die-steel , analyzed the HSM technology & CAM numerical control programming skill , and gives the instance of rigid die-steel HSM .

研究了稀土复合变质对新型铸造热锻模具钢（CHD钢）组织与性能的影响。

The effects of rare earth ( RE ) complex modification on structure and the properties of a new cast hot-work die ( CHD ) steel were investigated .

根据钢中碳化物相变热力学计算，研究了CrWMoVSi模具钢热处理过程的碳化物相变及其对热处理工艺的影响。

On basis of thermodynamic calculation the carbides transform and its influence on heat treatment process in a new kind of die steel Cr W Mo V Si are studied in this paper .

采用微观分析方法探讨了新型铸造热锻模具钢（CHD钢）的强韧化机理。

The nature of strength and toughness of a new cast hot working die steel ( CHD steel ) has been studied through the micro analysis in this paper .

Cr-Ni-Mo铸造热作模具钢热机械疲劳行为

Thermomechanical Fatigue Behavior of Cr-Ni-Mo Casting Hot Work Die Steel

由于表层形成一层TiN，Ti2N，TiC等化合物层，故提高了塑料模具钢的抗腐蚀性及耐磨性。

One layer of compounds consisting of TiN , Ti_2N and TiC was formed on the surface of these steels , which can improve the corrosive resistance and abrasive resistance of steels .

Thermo-calc在热作模具钢合金成分设计中的应用

Application of Thermo-calc Software to the Chemical Composition Design of Hot Work Die Steels