力学模型

并利用通用有限元软件ANSYS建立其力学模型并求解。

Utilized general FEM software ANSYS to establish mechanical model and solve .

低阈值电压RFMEMS开关的力学模型

Mechanical Model of Low Actuation Voltage RF MEMS Switches

基于高斯型脉冲驱动的类镍瞬态X射线激光的流体力学模型

Hydrodynamic model of transient Ni-like X-ray lasers driven by Gaussian laser pulse

基于GIS的土壤水蚀预报能量力学模型研究

Soil Erosion Prediction and Energy Exchange Modeling Using GIS

拱坝坝肩稳定的三维地质力学模型试验研究岩石力学CT技术概述

The Study on Experiments of a Geological Mechanics Model with Three Dimensions for the Stability of an Arch Abutment

建立了浸渍过程中树脂基体在纤维集合体内流动的统计力学模型。Resin方法进行纯化。

A statistical model is developed to study the flowing performance of resin fluid inside fibrous assemblies during the impregnation process .

利用统计力学模型讨论了与人类遗传病有关的DNA三核苷酸重复序列的弯曲和柔性。

We use a statistical mechanical model to discuss bending and flexibility of trinucleotide repeat sequences ( TRS ) which associate with several human genetic diseases .

文中，在建立屋盖智能隔震升船结构计算力学模型的基础上，建立了屋盖MR智能隔震系统对升船结构顶部厂房地震反应模糊控制的设计计算方法。

After establishing the mechanical model of intelligent isolation structure system , fuzzy control design methods of seismic response for top building of lift ship structure are developed .

SiC晶体PVT生长系统的流体力学模型及其有限元分析

A Hydrodynamics Model of Silicon Carbide Single Crystal Growth by PVT and Finite Element Analysis

通过双K断裂判据，以带切口的三点弯曲梁为断裂力学模型，分析了裂纹黏聚阻力对断裂过程的影响规律，计算该弯曲梁结构断裂试样的最大承担载荷；

Through the double-K fracture criterion and fracture model of three point bending beam , the effect of crack cohesive force on the fracture process is analyzed .

HSK工具系统的力学模型及其应用

Mechanical Model of HSK Tool System and Its Application

建立了CVT传动多组件的力学模型，解析了多层钢带受力和钢带传动滑移率。

Mechanics model of multi-layers metal ring and the model of transmission slip ratio were established .

发展了三维不连续变形分析（DDA）与有限元（FEM）耦合计算的力学模型。

A numerical model that coupled three dimensional discontinuous deformation analysis ( 3D DDA ) with finite element method was presented .

建立了ADSS微风振动力学模型，并进行了求解。

The mechanics model of ADSS aero vibration is not only elected but also solved .

为了研究黏性效应作用下的界面动态扩展裂纹尖端渐近场，建立了刚性-粘弹性材料界面II型动态扩展裂纹的力学模型；

A mechanical model of dynamic growing interfacial crack of mode II between rigid material and viscoelastic material was established in order to investigate viscous effect in dynamic growing interfacial crack-tip asymptotic field .

建立洞室围岩地质力学模型，采用平面有限元法，利用ANSYS有限元分析软件进行了数值模拟计算，对洞室进行了围岩稳定性评价。

Finally , it sets up geological mechanics models of underground cavern , accomplishes the numerical simulation applying 2D-FEM and using ANSYS software , and synthetically assesses the rocks stability of underground cavern .

对联系角焊缝，按其剪切工作情况，应用剪切力学模型，从本质上阐释角焊缝剪切强度系数（英国劳氏规范中的WeldFactor，ZC新《海规》中译为焊接系数）的力学概念；

As for the joining fillet welds , the mechanical conception of " the shear strength factor of fillet welds " ( or Weld Factor ) is described by the use of shear mechanical models .

在V形结构的基础上，通过简化力学模型的受力分析，建立力与变形之间的关系，从而获得W形结构的弹性变形公式。

On the basis of V structure , through analyzing the press from the model of mechanics predigested , a relation between strength and transmutation was set up , and the formula of elasticity transmutation of W structure was obtained .

应用ADINA软件，建立了可膨胀管膨胀过程的力学模型。

This article established the mechanics model of the expand process of the expandable casing with the elastic-plastic finite-element contact question of the ADINA software .

本文主要通过磁流变阻尼器来实现触觉反馈，磁流变阻尼器采用剪切工作模式，以Bingham模型进行建模，通过理论分析和研究计算，得到磁流变阻尼器的力学模型。

MR damper with shear work model is adopted and modeled with Bingham mode . Then the paper reaches a mechanics model by theory analysis and calculation .

首先回顾了简化动力学定轨的数学模型，然后结合两个CHAMP卫星星载GPS观测值的仿真算例，分析了各种力学模型对简化动力学定轨精度的影响。

Mathematical model of reduced-dynamic orbit was discussed firstly , and then the impacts of various force models on this orbiting method were illustrated with two simulation examples of onboard GPS observations on CHAMP satellite .

对于颗粒碰撞动力学，介绍线性、Hertz、DMT及BD等静态（或准静态）接触力学模型。

In the respect of particle collision dynamics , several static / quasi-static contact mechanics models were introduced , which consist of linear , Hertz , DMT and BD models .

采用Galerkin方法建立了贮箱平动激励下离散的液体受迫晃动方程，建立了三维受迫晃动响应的等效力学模型。

By using the Galerkin 's method and under the assumption of translational excitation , the discretized modal oscillational equations of forced slosh were derived . Also , the equivalent mechanical model of slosh was established .

对分层弹性地基中端承桩基础按winkler（温克尔）地基土模型并通过特性分析建立了合理的力学模型。

In this paper , the reasonable mechanics model are established to end-bearing pile foundation in layer elasto-foundation bed according to Winkler layer elasto-foundation bed soil model by means of characteristics analysis .

本文以F3精轧机为研究对象，建立了主传动系统和轧机机架系统的力学模型、数学模型，运用MATLAB软件计算出来两系统的固有频率和轧机机架的主振型。

The mechanics model and mathematical model of main transmission system and rolling mill system was established . The natural frequencies of the two systems and the main vibration modes of the mill housing were calculated by using MATLAB software .

针对焊接熔渣-金属冶金反应远离平衡的特性，从非平衡态热力学及液-液两相交互作用耦合的角度建立了液态熔渣组成中SiO2与熔敷金属间的化学反应热动力学模型。

To counter its characteristics of far from equilibrium , the metallurgical reaction occurred at slag / metal interface for SiO_2 in molten slag with deposited metal had been modeled in view of coupling non-equilibrium static thermodynamics with interacting principle of liquid-liquid phases .

本文讨论了YZ-55牙轮钻机整机静动态力学模型的建立。

In this paper , the establishment of static and dynamic mechanical models for whole structure of the YZ-55 blasthole drill is discussed .

主要叙述了在金刚石镀膜装置中，利用平行马赫探针测量了沉积室中的等离子体漂移速度，采用了Hutchinson的流体力学模型分析了数据。

The article discusses the use of parallel Mach probe to measure plasma flow velocity in deposit room of depositing diamond film device and the use of the fluid dynamics of Hutchinson to analyze the data .

本文引用古德曼（Goodman）层间结合力学模型来描述多层柔性路面结构层间的半结合状态，并基于这种力学模型给出了求解半结合N层弹性体应力、位移理论解的边界条件。

In this paper , Goodman 's constitutive law is adopted to describe the behavior of a partially integrated interface between the various layers in a multi-layered flexible pavement and the boundary conditions for solving the multi-layered elastic system with partially rough interface based on the constitutive law are given .

然后，建立了S形轨的力学模型及有限元模型，利用Dynaform软件分析了单元类型及坯料初始最小网格尺寸这两个算法参数对回弹计算精度的影响规律；

In the following , the mechanics and finite element model of S beam is founded and the rule that the element type , the least element size influence on springback is obtained by using the Dynaform software .