冷却板

结果表明，在炉身中下部和炉腹、炉腰部位炉衬内表面到冷却板前端的100mm范围内是炉衬耐材易损区和渣皮形成区；

The results show that the vulnerable zone of lining refractory and formation zone of slag skull are in a 100 mm range on lining 's inner surface from the middle / lower part of furnace stack and bosh to the front-end of cooling plate .

倾斜冷却板法在半固态加工中的应用

Application of inclined cooling plate in semi - solid processing

高炉冷却板的传热分析

Heat Transfering Analysis of Cooling Plate in The Blast Furnace

高炉冷却板热负荷监测系统开发

Development of the Monitoring System for Thermal Load of BF Cooling Plate

正常炉况下炉衬和冷却板稳态温度场的研究

Study on steady temperature field of cooling plate and lining of blast furnace

高炉冷却板的管理与维护

Maintenance and management of blast furnace cooling plate

异常炉况高炉冷却板及炉衬非稳态温度场

Unsteady State Temperature Field for Blast Furnace Cooling Plate and Lining in Abnormal Operation Process

优化的目的就是尽可能降低冷却板前端温度，保证凝结一层渣铁壳。

The a layer frozen slag-metal in the front of cooling plate was made for optimization .

机械振动对倾斜冷却板法制备亚共晶铝合金半固态组织的影响

Effect of Mechanical Vibration on Semisolid Microstructure of Hypoeutectic Al-Si Alloy Prepared by Sloping Plate Process

附有冷却板并采用双向冷却，循环效果快且均匀。

Equipped with cooling plate and cooled at two directional circulating , evenness & rapidity of effect .

大型高炉的密集式铜冷却板与冷却壁结合的炉衬结构是使高炉寿命达到18~20年的一项重要保证措施。

The lining structure with concentrated copper cooling plate-stave combined system for the large-scale blast furnace is the important guarantee of 18 ~ 20 campaign life .

本文对以托卡马克为聚变装置、氦气冷却板状元件包层的聚变-裂变混合堆进行了稳态、卸压和全厂断电断流的热工分析。

This paper presents the thermal analyses for steady state , depressurization and total loss of flow in the tokamak heliumcooling slab fuel element fusion-fission hybrid reactor .

采用激冷斜槽法和低过热法进行浇注料坯的试验，在试验中研究了不同浇注温度和冷却板倾斜角度对所浇注料坯的微观组织的影响。

The experience was conducted using cooling slope and low superheat processes , effects of pouring temperature and the degree of slope on the billet 's structure were researched .

冷却板周边的凸缘的存在，也减小了冷却板的磨损，延长了其使用寿命。

The existence of a flange at the periphery of the cooling plate also reduces the abrasion of the cooling plate , and prolongs the service life of the cooling plate .

后来，我们再用胶水补好，冷却板也加了冰块，但是气密性的问题还没有解决，另外，凸轮轴也做得不够好。

Then , we glued it again , and added some ice on the cold copper of engine , but the problem of gas-tightness didn 't be figured out . And , camshaft is not good enough .

中厚板控制冷却的板形控制与实践

Practice on shape control of plate in accelerated cooling

对流冷却下板状激光介质热效应的三维模拟

Three-dimensional simulation of thermal effects in a laser slab cooled by forced convection

冷却斜板铸造法是实现半固态铸造成形的一种简便而有效的方法，可以以较低的成本生产具有细小球晶组织的铸件。

The cooling slope casting is a branch of semi-solid casting technique , and it is also a simple and effective method to produce castings with fine globular microstructure at low cost .

因为真空或空气夹层具有较高的热阻，所以薄膜温度将明显高于冷却项板下表面温度而接近其周围室内空气温度。

The method is based on the theoretical analysis : because the layer is air or vacuum and has great heat resistance , the film temperature will be much greater than the panel temperature and near to the indoor air temperature .

采用ANSYS的水泥冷却机篦板有限元分析

Finite element analysis of cement cooler grate plate based on ANSYS

简述了SARMS冷却泵延时板的基本原理，介绍了维修思路和过程。

We briefly introduce the basal theory of time delay board in SARMS cooling pump and we also introduce mentality and process of maintain .

基于蒙特卡洛法的水泥冷却机篦板可靠性分析

Reliability Analysis Method for Cement Cooler Grate Plate Based on Monte Carlo

双冷却管双管板换热器的研发及其应用导热冷却测辐射热计

R D and Application of Dual-tube Dual-tube Sheet Heat Exchanger conduction cooling bolometer

层板发汗冷却推力室板片流道的调节功能试验

Experiment study for platelet slab flow channel control performance of platelet transpiration cooled thrust chamber

定径部分：采用真空负压定型及循环水冷却，不锈钢板制作。

Diameter setting part : It has adopted vacuum negative pressure setting and recycled water cooling and it is made of stainless steel .

本文通过冷却强化、板形控制等机理研究，论述中厚板淬火控冷装备技术的进展。

Progression of the quenching and control-cooling equipment technology of plate is discussed in the paper through the mechanism study on enhancing cooling , plate shape controlling and etc.

为了轧出质量良好的板材，许多钢铁企业及研究机构开发了轧辊交叉、倾辊、弯辊、分段冷却等各种板形控制技术来提高板形质量。

To rolled out high quality sheet , people developed cross-roller , sub-coolin , dumping roll , bending roll , and other shape control technologies to improve the quality of shape .

冷却塔环形基础板的平面应力分析

Plane Stress Analysis of Ring Baseplate of Cooling Tower

介绍一种改良的冷却装置的垂直板电泳槽

An improved vertical slab electrophoresis tank with cooling system

控制冷却技术在中板生产中的应用

Application of Controlled-Cooling Technology in Medium Plate Production