BOOTP

Intelligent Management of Industrial Ethernet Terminal IP Instrument Based on BOOTP

基于BOOTP的工业以太网IP仪表的智能化管理策略

This article proposed one kind of management device for industrial Ethernet terminal IP instrument based on BOOTP .

提出一种基于BOOTP的工业以太网终端IP仪表的网络化管理方案。

The BOOTP protocol is used for booting ( starting ) computers from the network .

BOOTP协议的作用是通过网络来重起（启动）计算机。

The Internet community first developed the BOOTP protocol to enable configuration of diskless workstations .

为了要能够为无硬碟的工作站进行组态，网际网路学会首先发展了BOOTP通讯协定。

BOOTP does not dynamically allocate IP addresses to a host .

BOOTP并没有办法动态的分配IP地址给一台主机电脑。

DHCP servers can lease IP addresses on different LANs using the BOOTP protocol .

DHCP服务器使用BOOTP协定能在不同的区域网络上出租IP位址。

G is the IP address of the gateway needed to reach the DHCP / BOOTP server .

G是到达DHCP/BOOTP服务器所需的网关的IP地址。

Filename specifies the Linux kernel to be loaded when servicing a BOOTP request .

filename指定响应BOOTP请求时需要装载的Linux内核。

This is used during the BOOTP phase of the installation to associate the LPAR with this host entry .

使用这个选项在安装的BOOTP阶段将LPAR和host条目关联起来。

The DHCP / BootP service is a program or device that will act as a host with a unique IP address .

DHCP/BootP服务可以是程序或设备，但必须在拥有唯一IP地址的主机上运行。

This means that the binding between the MAC address and the IP address must have already been configured in the BOOTP server .

也就是说，在BOOTP伺服器中，已经将所有MAC地址及其对应IP地址于事前定义好了。

If the DHCP / BOOTP server is on the local network , then use the IP address of the DHCP / BOOTP server instead .

如果DHCP/BOOTP服务器位于本地网络，则改用DHCP/BOOTP服务器的IP地址。

DHCP is a more flexible , backwards-compatible extension of BOOTP , and some of the latest systems can only boot using DHCP .

DHCP是更灵活的向后兼容的BOOTP扩展，一些最新的系统可能只使用DHCP进行引导。

For example , DHCP broadcasting data increase the burden on Internet , and DHCP inherits the redundant protocol header of BOOTP ( Bootstrap Protocol ) .

但随着网络的高速发展，DHCP的缺点也日益暴露，如：DHCP使用的广播数据增加了网络的负荷：DHCP本身还继承了自举协议（BOOTP，BootstrapProtocol）冗长的协议头部等。

This allows the system to start over from either another iSCSI disk or by using BOOTP / TFTP to load the kernel images and NFS to mount the root file system .

这允许从另一个iSCSI磁盘启动系统，或者使用BOOTP/TFTP装载内核映像并使用NFS挂载根文件系统。

Conversion of a scope to a DHCP Only scope or to a BOOTP Only scope is not allowed when DHCP and BOOTP clients both exist in the scope .

当DHCP和BOOTP客户端同时在作用域中存在，不允许将一个作用域转换为仅是DHCP作用域或仅是BOOTP作用域。

If you do not have a large computer which can act as a boot server , download our DHCP / BOOTP software so you can use a PC as a DHCP / BOOTP server .

如果您没有一个大型的计算机，可以作为启动服务器，请下载我们的DHCP/BOOTP软件，以便您可以使用一台PC作为一个DHCP/BOOTP服务器。

As described in the previous step of this article , your DHCP / BOOTP server is configured with the MAC address of the new LPAR , and it has an entry for the SUSE install program .

如本文的前一个步骤所述，配置DHCP/BOOTP服务器，使其带有新的LPAR的MAC地址，并且有一个针对SUSE安装程序的条目。