油底壳

现在ZO6准备增加另一项赛车元素&干式油底壳系统。

Now the ZO6 is ready for one more race car addition , a dry sump oil system .

基于结构刚度灵敏度分析的油底壳结构改进

Structure Improvement of Oil Sump Based on Structural Sensitivity Analysis

油底壳模态参数识别ITD法

The Identification of Modal Parameters of the Oil pan with ITD Algorithm

492Q发动机油底壳实验振动模态分析

Vibration modal analysis of 492Q engine 's oil pan

针对EA111油底壳铝合金压铸件的结构特点及工艺要求，介绍了一种切实可行的压铸模设计方案。

Aiming at the structure features and technological requirements for EA111 aluminum alloy oil tank , an available design plan for die casting die was described .

本文首先分别建立了CA6110柴油机的机体及油底壳的有限元分析模型，并利用实验模态的分析方法，对所建的有限元模型的合理性进行了验证。

This text built the FEA analysis model about the cylinder block and oil pan at first , and it proved that the FEA model was rational by using the analysis way of experiment model .

在标准的半消声室，用B&K3560型噪声测量分析系统，对4110Q柴油机整机和油底壳、飞轮壳、油泵，摇臂罩等零部件的噪声进行了台架试验研究。

The noise of 4110Q diesel engine and its oil pan , flywheel cover , oil pump , valve chamber has been studied by the analysis system of B & K3560 in the normal Semi-anechoic chamber .

含油量对油底壳固有频率的影响研究

Research on Dynamic Characteristics of Oil Pan with Quantity of Lubricant

发动机油底壳辐射噪声预测方法的研究

Research on Prediction Method of Radiated Noise of Engine Oil Pan

油底壳；有限元法；模态分析；结构参数；

Oil-pan ; Finite element method ; Modal analysis ; Structure parameter ;

柴油机柴油泄漏到油底壳的原因分析

Cause analysis of diesel oil leaking to crank case of diesel engine

内燃机油底壳加强板声学优化

Optimization of Noise Radiation of Engine Sump with Reinforcing Plate

油底壳冲压成形有限元分析

Finite element methods of oil sump sheet metal stamping process

摩托车发动机油底壳贮油量的选取

Selection of Oil Quantity in Oil Pan for Motorcycle Engine

油底壳成形过程数值模拟的优化建模研究

Modeling optimization research on numerical simulation of oil-pan forming process

定位凸台指向油底壳。

The fixing lugs point to the oil pan .

发动机油底壳振动与噪声辐射研究

Study on the Vibration and Acoustic Radiation of the Oil Pan of Engine

实测了发动机油底壳冲压成形后的厚度分布。

The thickness distributions of the oil pans after forming process were measured .

油底壳整体拉深成形中的破裂现象研究

Research on Cracking in Whole Deep Drawing of Oil-pan

松动油底壳螺栓，拆下每一面的前螺栓。

Loosen oil pan bolts and remove the front bolt at each side .

车用柴油机机体及油底壳的动态特性分析

Dynamic Properties of Vehicle Diesel Engine Block and Sump

对内燃机油底壳的加强板安装位置和长度进行了声学优化。

Noise radiation of engine sump with a reinforcing plate has been optimized .

裙边油底壳拉伸工艺分析及模具设计

Drawing Technology Analysis and Die Design for the Shirt Side Oil Bottom Shell

内燃机油底壳辐射噪声的计算研究

Study on Radiating Noise Calculation of Engine Sump

135油底壳冲压成形质量问题及其解决

Quality problems in sheet forming for 135 diesel oil pan and solution to them

油底壳模态和灵敏度分析

Modal and Sensitivity Analysis of Engine Oil Pan

油底壳一次拉延的计算机仿真与实验验证

Simulation and Experimental Examination for the One-Off Deep Drawing Formability of an oil Pan

机油参数对液固耦合油底壳辐射声场的影响

Influence of oil parameters on the radiant acoustic field of liquid-solid coupled oil pan

通常，应更换油底壳的紧固螺钉。

As a general rule , replace the fastening screws for the oil pan .

松开油底壳上的紧固螺钉。

Loosen fastening screws on oil pan .