安装误差

基于齿面3阶接触理论的曲线齿锥齿轮副的低噪声、低安装误差敏感度的传动性能设计

Transmission Performance Design of Spiral Bevel gears and Hypoid Gears with Low-noise and Low Misalignment Error Sensibility

捷联惯性系统初始对准中IMU安装误差及陀螺漂移的估计与补偿

Estimation and Compensation of IMU Misalignment and Gyros Drifts during SINS Initial Alignment

制作及安装误差对冷弯薄壁C型钢轴心压杆承载力的影响

The effect of facture and fixing error on bearing capacity of cold-formed thin-walled C steel column

用GPS标校平台罗经方位安装误差与航向精度测量

Using GPS to Correct Platform Compass Azimuth Installation Error and Measure Course Accuracy

CCD尺寸检测中安装误差对测量精度的影响

Effect of Alignment Error to Measurement Accuracy in CCD Dimension Measuring System

当传感器存在刻度系数误差、安装误差和测量偏差时，将会明显降低系统的FDI性能。

However , the sensor errors such as input axis misalignment , scale factor errors and biases , have significant effect on the FDI performance .

分析了在PAT过程中由于通信终端系统各光学器件安装误差所引起的光束矢量偏差，确定了终端光学路径中轴系误差的分类。

The beam vector deflection caused by the setting error of each optical element in the communication terminal system is analyzed .

研究结果对于合理选择和控制TI蜗杆副的安装误差以及选择轮齿修形参数具有重要意义。论文最后在对安装误差分析的基础上对蜗杆的修形分析进行了探讨。

Research results will be momentous significance for the proper selection and control of assembling errors of TI worm pair , as well as the selection of gear-tooth modification parameters .

MSP430单片机的三线摆转动惯量测量仪系统参数标定以及惯性元件安装误差测量与补偿技术研究

Three-line pendulum moment of inertia measuring instrument based on MSP430 Calibration for system parameters and scaling for installation errors of IMU

光学系统杂光指标PST的测量，包含了系统各种安装误差的影响，体现了系统杂光抑制的真实水平。

The PST of stray light includes the influence of system assemble error , and reflects the real capacity of stray light suppression .

利用AnsysAPDL语言编程对大量模型进行建模计算。得出各种情况下结构的单位耗钢量、节点半刚性对结构力学性能的影响以及安装误差引起的初始内力对结构内力的影响。

The modeling and analysis have been carried out in ANSYS APDL and the impact of steel dosage and semi-rigid connection on structure mechanical capability and the secondary stress on internal stress .

采用柱挠度曲线法（CDC法）分析了制作和安装误差（初弯曲、初偏心）对冷弯薄壁C型钢轴心压杆承载能力的影响。

Based on the column deflection curve method ( CDC method ), it was analyzed the effect of facture and fixing error ( initial bend and initial eccentricity ) on the bearing capactiy of cold_formed thin_walled C steel column .

VS新型垂直摆倾斜仪，由于其机械本体更稳定，仪器底板采用等腰三角形结构，增加了仪器的基线长度，进而减小了安装误差对仪器性能的影响；

The VS new vertical pendulum tilt meter has more stable mechanical body . Its bedplate uses the isosceles triangle structure , which increases the baseline length of the apparatus , as a result , the influence of install error reduces .

根据无陀螺捷联惯导系统（GFSINS）的工作原理，推导了理想条件下和有加速度计安装误差条件下的角速度解算方程；

Based on the operation principle of GFSINS , angular solution equations are derived respectively in the cases of ideal conditions and existing installation errors .

光电探测器（PDIC）的安装误差导致光学头的光学轴心与光电探测器的中心不重合。

The PDIC ( Photo detector integrated circuit ) position error causes the displacement between the optic axis of optical pick-up and the PDIC center .

安装误差角对陀螺加速度表的误差模型的影响

Research of Fix Error Angle for PIGA 's Error Models Effect

关于点接触齿面对安装误差敏感性的研究

The Sensitivity of Point - contact Tooth Surfaces to Mounting Errors

系统参数标定以及惯性元件安装误差测量与补偿技术研究

Calibration for system parameters and scaling for installation errors of IMU

硬磁盘驱动器中伺服盘片安装误差分析

Analysis of Mount Error of Servo Disk in Hard Disk Drive

传感器安装误差在声学多普勒计程仪中的校准

Calibration of transducer 's installation error for acoustic Doppler velocity log

考虑安装误差敏感性的螺旋锥齿轮主动设计方法

Active Design Method of Spiral Bevel Gears Considering Mounting Error Sensitivity

建立惯性仪表安装误差数学模型的理论研究

Theory Research on Angular Misalignment Error Models of Inertial Instrument

一种可消除安装误差影响的激光同轴度测量方法

A Kind of Coaxiality Measurement Method Unaffected by Installation Error

考虑安装误差网壳结构承载力概率分析

Probability Analysis on Ultimate Load of Lattice Shell with Initial Installment Imperfection

附着式轧制力传感器安装误差对测量精度的影响

Influence of Equipped Situation on the Attached Type Sensor ′ s Output

无陀螺仪惯性系统构型中安装误差分析与标定

Configuration fix-errors analysis and calibration for a gyro-free navigation system

安装误差对双圆弧齿轮传动误差的影响分析

Effect of misalignment on transmission error of double circular arc helical gearing

基于箱体零件安装误差的自动化控制方法研究

Research on Automatic Control Method of Housing Part Installation Error

垂直惯性基准零位安装误差的校正模型

Correction model of zero installing error of vertical inertial unit

验证现场测量和开口的安装误差，接受水平百叶。

Verify field measurements and installation tolerances of openings to receive horizontal blinds .