变形合金

研究了Al-B中间合金对用电解低钛铝合金制备的Al-Mg-Si变形合金的晶粒细化作用。

The grain refining effect of Al-B master alloy on Al-Mg-Si wrought alloy made of electrolytic low-titanium aluminum was investigated .

研究结果扩大了Al-B中间合金作为晶粒细化剂的使用范围，也为Al-Mg-Si变形合金的制备与晶粒细化处理提供了一条新的途径。

The results broaden the applying field of Al-B master alloy as grain refiner , and give a new way for preparation and grain refinement of Al-Mg-Si wrought alloy .

少量Mg、Zr对一种Ni-Cr-Ti型变形合金晶界滑移行为的影响

Effect of small amounts of Mg and Zr on grain boundary sliding of one Ni-base Superalloy

改善Mg-Zn-Zr系变形合金铸锭塑性的研究

Improvement of Plasticity of Wrought Mg-Zn-Zr Alloys

镍-铬-钛型变形合金长期时效的组织和性能

Structures and properties of a Ni-Cr-Ti type wrought superalloy after long-term aging

航空变形合金本构关系的模型及热力学参数计算

Aero-deformable alloy constitutive model data processing and thermal-dynamic coefficients calculation

电解低钛铝合金在变形合金6063中的应用研究

Study on Application of Electrolytic Low-Ti Al-alloy in 6063 Al-alloy

人工神经网络法在镍基变形合金蠕变断裂寿命预测中的应用

Application of Artificial Neural Network to Predicting Creep Rupture Life of Nickel-base Superalloys

能促进一些冷变形合金的再结晶过程；

The recrystallization of cold deformed alloys is promoted .

综述了磷对铁镍基变形合金的影响及机理。

The effects and mechanisms of phosphorus on Fe Ni based wrought superalloys are reviewed .

建立了常用航空变形合金本构关系和晶粒度演变模型。

So the common used aero-deformable alloy constitutive model and its grain size evolution model can be established .

变形合金的透射电镜照片表明位错的攀移和交滑移为合金变形的主要机制。

The TEM photo shows that dislocation climb and cross-slip are the important deformation modes of the alloy .

预变形合金强度、硬度的提高是由于θ′相的数目增加和尺寸减小。

The peak hardness and tensile strength of the pre-deformed alloy are increased because of quantity increasing and refinement of θ′ phase .

在试验数据的基础上，利用人工神经网络建立不同成分镍基变形合金的不同温度，外应力与蠕变断裂寿命之间关系模型，并进行网络训练，对合金的蠕变断裂寿命进行模拟。

Based on experimental data , an artificial neural network method is used to develop a model to predict the creep rupture life of different types of nickel-base wrought superalloys .

本文还讨论了变形合金在真空下，最佳调质退火温度和两相钨合金的形变特点、变形机制等。

The optimal temperature of vacuum annealing of deformed alloys , and the char-acteristics and mechanism of deformation of biphase W alloys have been discussed in this paper as well .

合金断口分析发现，铸态合金的断裂方式主要为脆性断裂，而挤压变形合金的断裂方式为韧-脆性混合断裂。

Alloys fracture surface analysis indicated that the fracture mode of as-cast alloys were mainly brittle fracture , while the fracture mode of the extruded alloys were ductile-brittle mixed mode fracture .

磷、硼微合金强化可成倍提高变形合金的持久寿命，降低蠕变速率一个数量级以上。

The addition of phosphorus and boron can prolong the rupture life of some wrought superalloys over 3 times , and lowers the constant creep rate by an order of magnitude .

通过对轧辊辊型的对比，认为二辊斜轧桶形辊穿孔机和二辊斜轧锥形辊穿孔机一样，也能适应连铸坯直接穿孔和高合金钢（包括部分难变形合金）制管的要求。

By comparison of roll types , both 2-barrel - roll cross rolling piercer and 2-cone - roll cross rolling piercer can meet the requirements of direct piercing of CC billets and tube making of high alloys ( including some hard reformed ones ) .

Ni基变形高温合金小孔攻丝扭矩的试验研究

Experimental Investigation on Small-hole Tapping Torque of Deformable Ni-base High-temperature Alloy

Al和Ca对变形镁合金性能的影响

Effect of Al , Ca alloying elements on mechanical behavior of wrought magnesium alloys

Si对一种镍基变形高温合金脆性转变的影响

Effect of silicon on the transition of brittleness in a nickel base wrought superalloy

稀土元素Ce对Al－Mg－Si变形铝合金组织的影响

Effect of Ce on the structure of Al-Mg-Si wrought aluminum alloy

稀土元素Ce对Al－Mg－Si变形铝合金铸态组织的影响及机理探讨

The effect of CE element on the cast structure of Al-Mg-Si alloy and its mechanism

Ce的加入对变形铝合金组织与疲劳性能的影响

Influence of Ce on microstructure and fatigue properties of wrought aluminum alloy

Al-Si系变形铝合金初晶硅尺寸的控制

Control of the size of primary silicon in wrought Al-Si alloy

微量硼和应变速率对变形TiAl合金室温力学性能的影响

Effects of trace boron addition and strain rate on room temperature mechanical properties of wrought TiAl Alloy

Nb对Ni-Cr-Ti型变形高温合金稳态蠕变行为的影响

Influence of Nb on steady-state creep behaviour of Ni-Cr-Ti type wrought superalloy

轧制变形铝合金微观组织与织构的EBSD研究

EBSD investigation on microstructure and texture in rolling aluminium alloys

双轴加载下冷变形Zr-4合金的循环变形行为及其微观机理

Cyclic deformation behavior and microscopic mechanism of cold-worked Zr-4 alloy under biaxial loading

Al-Cu-Mg系变形铝合金厚膜阳极氧化工艺研究

Studies on the Thick-Film Anodizing of Al-Cu-Mg System Aluminium Alloys